Print Reading for Engineering and Manufacturing Technology 3rd Edition Solution Manual

Name: Print Reading for Engineering and Manufacturing Technology 3rd Edition Solution Manual
Brand: Academic Documents Platform
Price: 10 USD
Availability: InStock
Author: Sebastian Lopez

Print Reading for Engineering and Manufacturing Technology 3rd Edition Solution Manual is your ultimate textbook solutions guide, providing answers to the most difficult questions.

Sebastian Lopez

Contributor

4.4

4 months ago

Preview (16 of 80)

Textbook Solutions Manual
Print Reading for Engineering & Manufacturing Technology
Third Edition
David A. Madsen
David P. Madsen

Chapter 1 – Introduction to Engineering and Manufacturing Technology Print Reading
Print Reading Problem Solutions
Problem 1.1
Given the drawing shown on page 15, answer the following questions using short, complete
statements.
1. Give the drawing title. TRIAL HEAD EXTRA LONG
2. Identify the drawing number. 2060101
3. How many time has this drawing been revised? 0
4. How many sheets are there with this drawing? 1
5. What is the drawing scale? 2:1
6. Identify the sheet size. B
7. Give the material used to make the part. ASTM B211 ALLOY 6061 T651
8. Identify the view projection used on this drawing. THIRD ANGLE PROJECTION
9. Specify the finish used for this part. 4 Ra MAX ON OUTSIDE SURFACE. 111 Ra
MAX ON INSIDE SURFACE.
10. Give the initials of the person who approved this drawing. DAS
Problem 1.2
Given the drawing shown on page 16, answer the following questions using short, complete
statements.
1. Give the drawing title. BODY ASSEMBLY - 4 PORT OIL PUMP
2. Identify the drawing number. 8-N016
3. How many time has this drawing been revised? Twice, two times, or B
4. How many sheets are there with this drawing? 1
5. What is the drawing scale? 1:1
6. Identify the zone where the (2X46.3) dimension is located. C4
7. Give the COMPANY NAME. SYNERJECT
8. Identify the view projection used on this drawing. THIRD ANGLE PROJECTION
9. Give the sheet size. A3

10. Give the initials of the person who approved this drawing. KLL
11. Give the description of the first revision. ECN 1510
12. Give the description of the first revision. A RELEASE FOR PRODUCTION
13. Give the description of the current revision. B 1 REVISED APPLICATION TABLE, B
2 REVISED 8-N014
14. Identify the zone where the second part of revision B is located. A6
15. Identify the zone where the (58.51) dimension is located. B5

Chapter 2 – Communicating with a Sketch
Sketching Problems – Solutions
PROBLEM 2.1
On a separate sheet of paper list the length, direction, and proportion of each line numbered in
the drawing for Problem 2.1. Remember to use the measurement line method described in this
chapter. Do not measure the lines with a scale. Example: Line 2 is the same length as line 1 and
touches the top of line 1 at a 90° angle.
Student answers may vary. There are possible answers: Line 3 is vertical and is about 4
times as long as Line 4 and touches the right end of the Line 4 at a 90˚ angle. Line 4 is
horizontal and is about the same length as Line 5 and meets 90˚ at the top of Line 5. Line 6
is horizontal and is about twice as long as Line 5. Line 6 meets 90˚ at the bottom of the Line
5.

Loading page 6...

Loading page 7...

Loading page 8...

PROBLEM 2.7
Find a stapler, tape dispenser, coffee cup, or something similar and sketch a 2D frontal view
using the block technique on a separate sheet of paper. Do not measure the object. Use the
measurement line method to approximate proper proportions.
Solution will vary depending upon the selected object
PROBLEM 2.8
Given the pictorial drawing of the V-block for Problem 2.8, sketch a front and right-side view.
Use the measurement line method to approximate dimensions when preparing your sketch on a
separate sheet of paper.

Loading page 9...

CHAPTER 3 – Scales and Precision Measurement
Chapter Problems - Solutions
PROBLEM 3.1
Given the following civil engineer’s scale, determine the readings at A, B, C, D, and E.
A .5_____________________________
B 1.1_____________________________
C 2.25____________________________
D 3.6_____________________________
E 4.4_____________________________
PROBLEM 3.2
Given the following architect’s scale, determine the readings at A, B, C, D, E, and F.
A 1/8___________________________
B 5/8___________________________
C 1–5/16________________________
D 1–3/4_________________________
E 2–1/4_________________________
F 2–15/16_______________________
PROBLEM 3.3
Given the following metric scale, determine the readings at A, B, C, D, and E.
A 10_______________________
B 40__________________________
C 76________________________
D 120________________________
E 166________________________

Loading page 10...

PROBLEM 3.4
Given the following mechanical engineer’s scale, determine the readings at A, B, C, and D.
A 1.0_________________________
B 5.0________________________
C 6.5_________________________
D 10.8________________________
PROBLEM 3.5
Determine the readings in inches on the following vernier calipers.
1. Reading 2.30________________
2. Reading 1.75________________
3. Reading 4.009_______________
4. Reading .563________________
PROBLEM 3.6
Determine the readings in millimeters on the following vernier calipers.
1. Reading 15__________________
2. Reading 7.12_________________
3. Reading 27.08________________
4. Reading 50.40________________
PROBLEM 3.7
Determine the readings in thousandths of an inch on the following micrometers.
1. Reading 0.150__________________
2. Reading 0.520__________________
3. Reading 1.393__________________
4. Reading 2.859__________________

Loading page 11...

Loading page 12...

Chapter 4 – Reading Lines and Lettering on a Print
Print Reading Problems Solutions
Problem 4.1
Given the print found on page 59, name or identify the items labeled A through P.
A Visible line
B Centerline
C Extension line
D Extension line
E Dimension line
F Dimension line
G Break line or Short break line
H Viewing plane line
I Cutting plane line
J Section line
K Leader line or Leader
L Extension line
M Border line
N Microfilm alignment arrow
O General notes
P Specific or local note
PROBLEM 4.2
Given the print found on page 59, identify the lines labeled A through M.
A Visible line
B Centerline
C Extension line
D Dimension line
E Hidden line
F Leader line
G Cutting Plane line

Loading page 13...

H Phantom line
I Centerline
J Visible line
K Section lines
L Dimension line
M Leader line
Answer the following questions by referring to the print shown on page 59: (Some questions
may require you to review previous chapters.)
1. Name the system of numbers and letters in the margin that allow you to read the print like
a road map. Zone or zoning.
2. Name and give the function of the arrow symbols found at the middle of the horizontal
and vertical border lines in the margin. Microfilm alignment, or centering, arrows are
placed in the margin of drawings for use in microfilm alignment. Microfilm is a film
on which drawings or other printed materials are photographed at greatly reduced
size for ease of storage.
3. Identify the type of notes found at D8. General notes.
4. Name the type of note found at A3. Specific or local note.
5. Identify the type of note found at A3. Specific or local note.
6. Give the drawing title. SADDLE-TELESCOPE LENS MTG
7. Identify the material used to make this part. AL 5052-H32 .05 THICK
8. Specify the sheet size used for this print. D
9. Give the CAGE code. 64869
10. Identify the finish. CHEM FILM PER MIL-C-5541, CL3

Loading page 14...

Loading page 15...

Loading page 16...

13 more pages available. Scroll down to load them.

Preview Mode

100%

Study Now!

XY-Copilot AI

Unlimited Access

Secure Payment

Instant Access

24/7 Support

Document Chat

Document Details

Subject

Engineering

Print Reading for Engineering and Manufacturing Technology 3rd Edition Solution Manual

Study Now!

Document Details

Related Documents

Print Reading for Engineering and Manufacturing Technology 3rd Edition Test Bank

ENGR 111 Spring 2025 ScheduleFeb 19

MyOakton Instructions Change Term View Placement I

Computer Assembling Plant Design

Reliability Analysis and Maintenance Strategies for Complex Systems and Components

Analysis and Calculations of Resistances, Wire Sizes, and Magnetomotive Force in DC Machine Field Windings

ECET105 � Digital Fundamentals Homework Assignment #5

INDE 2333 Engineering Statistics I Practice Exam 2

Test Bank for Automotive Service Management, 3rd edition

Solution Manual For Refrigeration and Air Conditioning Technology, 8th Edition

Company

Explore

Study Tools